Although we work hard to have these sites taken down as we find them, identifying them all can be difficult and we have heard stories of our customers being duped out of their hard-earned money by these criminals. In recent months, we have seen an uptick in fraudulent websites that mimic the look and feel of Ruger's website and claim to be authorized Ruger retailers.
#RUGER LC380 TRIGGER REMOVAL INSTALL#
On the International Model, carefully slide cap onto the end of the stock and install and tighten screw.Warning: Fraudulent Websites - Think Before You Click Instead, alternately tighten each one-a partial turn at a time-so that the screws will be tightened equally until both are snugly tightened. (This screw is angled and draws the barrel-action assembly into the bedding surface of the stock.) Tighten the two trigger guard screws as follows: Do not tighten one screw all the way and then tighten the other.
Install floor plate hinge assembly and firmly tighten screw. Replace trigger guard and loosely install screws. Place barrel-action assembly-with magazine box in place-into stock. To replace stock: First, install magazine box on receiver. Align the locking lugs with the channels in each side of the rear of the receiver and partially insert the bolt. With bolt handle in an upward position and bolt head away from you, align the extractor with the right hand locking lug. To replace bolt: Place safety in its off position. When the firing pin assembly is correctly positioned in the bolt body, the restraining pin can be removed. When the firing pin assembly is being turned into the bolt body, it may be necessary to use the restraining pin as a lever to slightly retract the cocking piece nose so it can be moved into the notch. Note that there is a shallow notch on the rear end of the bolt body-at the end of the cam cut-into which the nose of the cocking piece 'fits'. The assembly is properly positioned in the bolt when the flat on the bottom left side of the bolt sleeve (front of bolt facing you) is aligned with the flat on the bottom end of the bolt handle.
To reassemble firing pin assembly into bolt, screw the assembly fully into the bolt. In the event that further disassembly is required, do not disturb the trigger adjustment screw (engagement) (Part D-22) or the trigger adjustment screws (over travel) (Parts D-45 and D-44.) See Figure 4. Lift the receiver at the same time as the barrel is lifted so that the barrel-receiver assembly comes out of the stock level, and not at an angle.ĥ. It can be lifted out with the barrel-receiver assembly, but it must be done with great care.) Lift barrel from the stock very carefully. (If magazine box does not come out readily, do not force it. Next, loosen and remove the screw which is to the rear of the trigger guard. Next, loosen and remove the screw that is just forward of the trigger guard. To Remove Stock: Open floor plate and while holding it up out of the way, loosen and remove the screw that holds the floor plate hinge assembly. Special note regarding disassembly of the International Model: Before attempting to remove the stock (Mannlicher-type) as described in paragraph number 4 (below), first remove the cap screw (D-13200) and then the cap (D-01340).Ĥ. Also, special tools are required to correctly reassemble this part.
The parts are under great spring pressure and if disassembled could fly apart with sufficient force to cause serious injury. (Caution: Do not remove the restraining pin until firing pin assembly is reassembled into bolt.) CAUTION: The firing pin assembly is intended to be a permanent assembly and should not be disassembled. Unscrew firing pin assembly and remove from bolt. NOTE: The pin or nail should be as close as possible in size to the hole diameter, and at least 2 inches long so that it can be used to 'lever' the firing pin to the rear when reassembling the firing pin assembly into the bolt. To remove firing pin assembly from bolt: With bolt out of the rifle and firing pin cocked, insert a pin or nail into the "disassembly hole", as shown in Figure 1. To remove bolt: (Safety must be off.) Open bolt and pull to the rear while at the same time pivoting open the bolt stop (located on the left side of the receiver). Check to ensure that chamber and magazine are clear of ammunition.Ģ. DISASSEMBLY WARNING: Never clean, lubricate, disassemble or work on a firearm while it or its magazine is loaded.ĬAUTION: Before starting disassembly, remove sling, scope and rings and place the rear sight blade in its down (flat) position.ġ.